Network Snapshot
Record this computer's interfaces, routes, DNS, neighbor table and listening ports, and compare two snapshots.
Sidebar group: Troubleshooting · Works offline: yes (it reads local configuration only and sends nothing) · Needs admin rights: no
When to use it
- Before and after a change: a firewall policy push, a VPN client upgrade, a driver update. Compare the two snapshots to see exactly what moved.
- Connect and disconnect a VPN, and see which routes, DNS servers and interfaces it adds.
- "It worked yesterday": compare today's snapshot with one saved earlier.
- Compare two computers that should be configured the same, using Save file... on one and Open file... on the other.
- Spot a gateway MAC address that changed for the same IP, a possible sign of ARP spoofing.
Quick start
- Click Take snapshot. It takes a few seconds and is saved automatically.
- Optionally type a Label (for example
before VPN) and click Save label. - Make your change, then click Take snapshot again.
- Switch to Compare. The newest snapshot is already selected as After (B) and the previous one as Before (A).
- Click Compare and read the Notable changes list, then each section tab.
- Use Export to save the snapshot or the comparison as a report, or add it to a project.
Inputs and options
| Field | What it means | Default / accepted values |
|---|---|---|
| Take snapshot | Reads the current configuration and saves it. | |
| Open file... | Adds a snapshot file saved with Save file... (for example from another computer) to the list. If its id clashes with a saved one, it gets a new id. | .json snapshot files up to 16 MB |
| View / Compare | Switches between viewing one snapshot and comparing two. Compare needs at least two saved snapshots. | View |
| Saved list | Every saved snapshot, newest first: label or host and time, OS, and counts. A failed tag means a section could not be read. | |
| Label | A name for the selected snapshot. Press Enter or click Save label. | Empty; up to 200 characters |
| Section tabs | Interfaces, Routes, DNS, Neighbors, Listening ports, each with its row count. | Interfaces |
| Filter rows | Shows only rows containing the text, in any column. | Empty |
| Save file... | Writes the selected snapshot to a JSON file. | |
| Delete | Removes the selected snapshot after confirmation. | |
| Before (A) / After (B) | The two snapshots to compare. Swap exchanges them. | Previous and newest after a new snapshot |
Reading the results
View shows the time, host name and OS, then one table per section:
- Interfaces: name, state (up or down), MTU, MAC address and every address in CIDR form, including IPv6 link-local.
- Routes: IPv4 and IPv6 routes with destination, gateway (
on-linkwhen there is none), interface and metric. On Linux the main table is read; on macOS the ARP/ND host entries thatnetstat -rnmixes into the table are left out (they appear under Neighbors). - DNS: servers and search domains per scope. macOS shows the default resolver and any per-domain resolvers; Linux shows
/etc/resolv.confand, with systemd-resolved, each link; Windows shows each interface and the global suffix search list. - Neighbors: ARP (IPv4) and neighbor discovery (IPv6) entries: IP, MAC, interface and state. Multicast and broadcast entries are left out.
- Listening ports: TCP sockets in LISTEN and bound UDP sockets, with process name and PID where the OS shows them.
A yellow box lists any source that failed and why. A grey box shows limits that applied (for example "your own processes only"). Sources at the bottom lists the exact command behind every section.
Compare shows:
- Notable changes: a MAC address that changed for the same neighbor IP, a default route that was added, removed or changed, DNS servers or search domains that changed, and new listening ports.
- One tab per section with the number of differences. Each row is added (only in B), removed (only in A) or changed (in both, with the differing fields named).
Worked example. Snapshot A is taken on a laptop, then a VPN client connects and snapshot B is taken. The comparison shows:
- Interfaces:
utun4added with198.51.100.23/32. - Routes:
IPv4 default via 198.51.100.1 dev utun4added, andIPv4 203.0.113.0/24 via 198.51.100.1 dev utun4added. - DNS:
Default (utun4)added with198.51.100.53, searchcorp.example.com.
The notable list repeats the new default route and DNS scope at the top.
What the results do and do not tell you
- A snapshot is a point in time. Neighbor entries age out and idle listeners come and go, so an entry missing from one snapshot is not proof that something was removed.
- Neighbor state changes (reachable, stale, delay) are not counted as changes; only a different MAC for the same IP is. A changed MAC is expected after a device or NIC swap, a failover, or a VRRP/HSRP move.
- A listener whose process restarted with a new PID is not a change; a different program on the same port is.
- Rows are matched by a key: interface name, route (family, destination, gateway, interface), DNS scope, neighbor IP and interface, listener protocol, address and port. If several rows share a key (equal-cost routes, for example), the first is compared.
- Comparing snapshots from two different computers is allowed, and the panel warns about it; expect most rows to differ.
- Route metrics are not shown on macOS (
netstat -rnhas no metric column). Windows shows the route metric only, not the interface metric added to it.
Online activity and privacy
Nothing is sent on the network. The tool runs local, read-only commands:
- macOS:
ifconfig -a,netstat -rn,arp -an,ndp -an,scutil --dns,netstat -anv, andlsofas a fallback. - Linux:
ip -j addr,ip -j route(IPv4 and IPv6),ip -j neigh,ss -Hlntup,/etc/resolv.confandresolvectl. - Windows: one PowerShell call using
Get-NetAdapter,Get-NetIPAddress,Get-NetIPInterface,Get-NetRoute,Get-DnsClientServerAddress,Get-DnsClient,Get-NetNeighbor,Get-NetTCPConnection,Get-NetUDPEndpointandGet-Process.
Each command has a 30 second timeout and a 16 MB output limit. Snapshots are saved as JSON files in the app data folder, under snapshots/ (see Privacy and data). They contain your host name, addresses and process names; use a redacted export before sharing.
Export and projects
Export on a snapshot writes a report with a summary, the sources and every section as a table. Export in Compare writes the summary counts, the notable changes and a table of differences per section. Both can be added to a project. See Export and redaction. Save file... writes the raw snapshot for use in another copy of Net3PO; it is not a report.
Platform notes
- macOS: process names come from
netstat -anv. When the app is started in a way that macOS hides other processes' sockets from (seen with unsigned builds), the tool falls back tolsof, which lists only your own processes, and says so in the grey box. - Linux: needs
iproute2(ipwith JSON output,-j) andss, which current distributions include. Without root,ssnames only your own processes; other sockets show "process not visible". The DNS section adds systemd-resolved scopes whenresolvectlis present. - Windows: Windows PowerShell 5.1 (built in) is used. All cmdlets work for a normal user and show process names for every listener.
Troubleshooting
A section shows "failed" with "ip is not installed or not on PATH". Install iproute2. Very old distributions without ip -j JSON output are not supported.
"unexpected ip output" or "unexpected PowerShell output". The command printed something the parser did not recognize. Note the OS version and report it.
Listening ports shows "your own processes only" on macOS. See Platform notes. Ports held by system services may be missing from that snapshot.
"not a Net3PO snapshot file". The file opened with Open file... is not a snapshot saved by this tool.
Compare is greyed out. Take or open at least two snapshots.
Related tools
- Config Diff to compare device configurations.
- Port Scanner to check listening ports from another host.
- MAC Vendor Lookup to identify a neighbor's MAC address.
- Visual Traceroute to see where routed traffic goes.